Front Hubs for Lamb Components strut suspension. Older..used on pro stocks and high end comp eliminator cars. Looks to be a 5X4.75 bolt pattern as near as I can tell.$350 shipped to lower 48 I know nothing else other than what I posted on these hubs.. if using paypal only verified paypal users...or postal money orders.... Waitsburg, WA 99361 (509) 520-7667
older Ed Hamburger blow by tool for use in the dyno room. Verified Paypal or postal money order only. Waitsburg, WA 99361 (509) 520-7667
Toyo Eclipse Tires, 205s on 15" Matte Black Five Spoke Focal Rims, The tires are barely used (80 to 90% tread left) full warranty from les schwab. I sold the car and kept the tires, now I need to sell them. I paid $xxxx or so, asking $750. text or call 509.200.xxxx
NOS wiper switch in box $200 shipped USA 211 955 501C _________________ www.rockyjennings.com
Brand new t-3 rear drums, very nice can be installed on a bug. Early models will need machining done to the drum, also (you will need to find T-3 backing plates, shoes & hardware) Drums only $125 each + shipping. I can not sell this drum in Califorina, Sorry. All out of USA sales that a customs form has to filled out are subject to a minimum of a $10 fee. No AK or HI sales. Thanks Rocky _______...
. Note price increase: Very Special repair oil pan stud 7mm on one end 6mm on the other. All you have to do is tap the case with a 7x1mm tap and you have made the stripped out stud repair its that easy. If you are repairing the stripped out hole with the engine in the car a bit of grease on the end of the tap will catch most all of the shavings for the rest i use a Q-tip to get them. No drillin...
I have been asked a number of times to do the bushing install. So now I will do the service for those who would like me to rebush your nose cone housing any year. (Not the 091 housing). On the early housing I can set them machine the end and install the outside bushing & install a bushing on the inside, then hone to size ( I will need your hockey stick ) and return shipped back to you ready to ...
Weber DCNF & IDF idle jet holders set of (4) with 4 new o-ring seals (no jets). Price set of (4) shipped USA $26. Use 8mm socket or flat tip screw driver to install. Makes installing them on the back side of a DCNF with a 8mm - 5/16 socket a easy install. Set of (4) shipped free USA $30. I do not take C/Cs over the phone Payment only through paypal at [email protected]
Four Silicone Intake Boots for all busses from 72 -91 vanagons & 914 Replaces VW P/N 039 133 241. These are the very best boots you can buy. Used on Race Turbo Engines. 4 Boots get rid of the old dried & cracked boots. I have them in blue or black. $52. Note NO clamps are included in the $52 price. (If you want the 8 clamps add $24). Note: 2.1 engines do not need clamps on the boots as they fit...
This kit is NOT the cheap split bushing or rolled style. These bushings are CNC made in the USA. Bus, bug and T-3 nose cone seal bushing kit for the early nose cones that did not come with a seal. And the late nose cones with a seal. This kit will not fit 091 nose cones as they have brgs to support the hockey stick. I just need to know what size on the O.D. of your bushing so I can get you the ...
WBX Vanagon Gasket Kit with flywheel & pulley seals & sealants needed to rebuild your Water Boxer engine. $125 shipped USA All out of USA sales that a customs form has to filled out are subject to a minimum of a $10 fee. my email & paypal is [email protected]
Stainless steel Dash switch tool fits most all air cooled dash switches I have sold over 2000 of this tool. Works great. $30 shipped USPS PM USA paid via paypal. Out of the USA add $35 my email & paypal is [email protected]
WXB VW New Hydraulic lifters. Very nice HYD lifter set. $106 a set of 8 shipped USA. If the price is in the heading of the ad that means I still have them in stock. All out of USA sales that a customs form has to filled out are subject to a minimum of a $10 fee. I only take Paypal. email me at [email protected]
These cylinder shim spacers are used to get 94mm air cooled cylinders in the waterboxer block that you use the bug style head stud spacing. I also have smaller I.D. rings so you can install 90.5s & 85.5 cylinders as well. I have sold over 80 sets of these spacer shims. You may have to use a rat tail file to open the notches a bit for your size head studs 8mm or 10mm. If you what the notches cut...
New Heavy duty (will do the k-800 springs) valve spring compressor tool used to remove springs (PLEASE NOTE: the following, new style without the long handle you use your ratchet for the handle) for heads without removing the heads from the engine. For using single springs to break in cam for dual springs. The spark plug fitting is for putting compressed air into the head to hold the valves so ...
WBX vanagon Metal coolant flange replace your old leaking plastic one on your 86-91 2.1 with a cnc machined one P/N 025 121 160 D. NLA @ the dealer or $20 shipped from me. A Vanagon owner just emailed me with his story of broken alt belt that sheared off his plastic nipple on his coolant flange and was a PITA to find something to get him on the road again. If yours is plastic replace it before ...
Do your own full flow install. (Note the kit does not come with the 3/8 - 18 tap.) This kit will let you with a drill press. Drill, clearance and tap straight the engine case for full flow oil filter or oil cooler. Kit comes with correct length drill, clearancing tool, and chuck starter so the tap gos in straight. Pictures show steps on how to do the full flow machine work. If you want a brass ...
Flycutter holder with cutter blade & 3/4 shank with 7/8 x 9 thread for flycutter.* in stock. You can open your own heads & cases with a milling machine and a 3/4 collet. Both pieces $115 shipped USA. If you only want the flycutter holder with blade $70 + shipping or only the blade that's $32 or threaded 3/4 shank $65 + shipping. The threaded shanks are CNC made I can not turn them down to anoth...
I make the bushings so you can put a bug lifter cam in a waterboxer block . You will have ream or hone the inside of the bushings to fit your lifters. The O.D. of the bushings will need to be de-burred at the oil holes. When you get ready to install you have remember that you are going to use the bug mushroom headed lifters and you will need to remove some of the top of the aluminum WBX lifter ...
This angle plate is for cutting of spring seats for dual valve springs & trimming of the tops of the valve guides for larger lift cams,(I have the RJE spring cutter tool listed on the samba), it can also be used to cut valve seat pockets for larger valve seats and to core out valve guides ( I have the RJE core drills listed on the samba). It can be used to open the areas in the combustion chamb...